Six lines, one cutting bed, every piece stitched in Aljunied
AGVA SINGAPORE PTE LTD runs a compact canvas case bench at 625 Aljunied Road #04-07 Aljunied Industrial Complex, Singapore - 389836, Singapore (SG). The bench offers six services, each with a defined scope, a material list and a predictable lead time. This page describes what each service covers, how it is quoted, and what a client receives at the end of a run.
Zip well sample from the bench: tape set flat, brass slider seated, edge bound before the body is joined.
Laptop Sleeve Runs
The laptop sleeve is the most requested piece on this bench, and the one with the least room for error. A sleeve has to fit a specific device, allow for any cover that stays on the machine, protect the corners, and open wide enough that the laptop can be removed without being dragged across the edge. We cut the pattern from the measured device envelope, add a padding allowance of a set thickness, and mark the seam line on the canvas before anything is trimmed.
The standard build uses a heavy cotton canvas outer shell, a padded inner wall faced with mint liner cloth, and a full-length brass zip set into a wide well so the tape never folds back on itself. The edges are bound rather than folded so the sleeve keeps a clean line after repeated use. We offer a plain face or a stitched panel face, and we can set a small brass plate at the corner for a run identifier.
Runs are quoted in two stages. A single sample is built first and sent for evaluation so the fit can be confirmed against the actual device. Once the sample is approved it is signed off on paper and kept on the shelf. A production run of twenty or more is then scheduled against the approved sample, with a stitch count recorded for each piece. Repeat orders are matched to the archived sample so the second batch is indistinguishable from the first.
Desk Organiser Lines
A desk organiser has a harder job than it looks. It is lifted by one corner, pushed across a table, filled with cables and adapters, and asked to hold its shape for years. Our organisers are built on a board-reinforced base wrapped in canvas, with internal dividers that are stitched rather than glued so the wells do not peel open after a season of use.
We offer three standing layouts: a cable tray with a single long well and two short end wells, a pen and tool tray with staggered dividers, and a drive and card tray with shallow compartments. Each can be adapted for a specific item list, and the divider positions are drawn to the millimetre on the cut sheet. The closure is a strap and brass buckle that wraps the tray when it is carried between desks or packed into a bag.
Organiser lines are often ordered alongside sleeves as part of a single desk kit. When they are, we align the canvas dye lot and the liner colour so the two pieces read as a set. The bench also builds denim and waxed panel variants on request, though the standard line stays in natural canvas for ease of repair.
Travel Case Builds
Travel cases on this bench are planned around a packing list rather than a standard frame size. The first step is to lay out the kit that has to travel: instruments, samples, presentation materials, tools or test equipment. We measure the whole set, decide how it should be divided, and design the internal walls to hold each group in place without rattling against its neighbours.
The build then moves to the closure. A case that will be checked onto a flight gets a heavier zip, a reinforced handle and a strap that wraps the body rather than relying on the seam. A case that travels by car or by hand may use a lighter closure and a simpler handle. We test the packed case on a scale and by carrying it across the workshop before the run is approved, because weight distribution is the most common reason a case fails in use.
Every travel case is delivered with a packing diagram, a small drawing that shows where each group of items belongs. That diagram is also kept on file with the cut sheet so a replacement case, or an additional case for a new team member, can be built to the same layout years later.
Custom Canvas Panels
Not every client needs a finished case. Some need panels: loose canvas pieces cut, bound and finished to a specification that will be assembled into another product. We cut drawer liners, case skins, modular dividers, screened backdrops and panel sets for small workshops that build their own carriers.
Panel work is quoted from a drawing. The client supplies the dimensions, the fold or binding detail, the grommet positions and the stitch pattern. We produce a single panel as a proof, check the edge finish and the hardware placement, then run the batch. Panels are delivered flat, bundled by size, with a cutting label on each bundle so the receiving workshop can identify the set without unfolding it.
Because panels are a looser product than a finished case, we keep the tolerances explicit in the quote. Length and width are held to a stated margin, grain direction is marked, and any shrinkage allowance is recorded. If a panel job runs into a detail that the drawing does not cover, the bench stops and asks rather than guessing, since a hidden assumption is the most expensive thing in a bulk panel order.
Bulk Corporate Orders
Bulk orders are where the bench earns its keep. A corporate run might be sixty sleeves for a device refresh, two hundred organisers for a conference, or a mixed set of cases and panels delivered in three batches across a quarter. The work is planned backwards from the delivery date, with the approved sample, the hardware sheet and the material order fixed before the first cut.
Each bulk order is assigned a run reference that appears on every job card and on the delivery note. The client receives a sample retention notice confirming that the approved piece is held on the shelf, a hardware approval sheet listing every buckle, slider and rivet, and a batch schedule showing what ships when. If a material has to be substituted for any reason, the bench contacts the client before cutting rather than after.
We keep bulk runs in the same workshop as single pieces, which means the same hands set the hardware and the same eye checks the edge binding. The bench does not sub-contract stitching to a third party. That choice limits how large a run we accept in a given month, and we say so honestly when a schedule cannot be met.
Repair and Refit Service
A canvas case should not be discarded because one zip has failed or one strap has worn through. Our repair and refit service takes pieces that are still in daily use and returns them to service: replacement zips in brass or nickel, rebound edges, new liner cloth, fresh straps, and hardware swaps where a buckle has lost its spring.
Every repair begins with an assessment. We look at the stitch integrity along the seams, the condition of the canvas at the fold lines, and the state of the hardware. A quote follows that assessment, and it covers only the work that will genuinely extend the life of the piece. If a repair would cost more than a replacement, we say so and offer the replacement instead.
Refits are also used when a device changes. A sleeve built for an older laptop can often be re-cut and re-lined for a new device of a similar envelope, and an organiser can be re-divided for a new desk layout. The original cut sheet helps here; if we built the piece, we can usually match the new work to the old exactly.
How every job moves through the workshop
The six services differ in output but share one process. A job enters the bench through a measure, passes a drawing review, produces a sample in final material, runs in recorded batches, and ends at a fit check before packing. The stages are the same whether the job is one sleeve or two hundred organisers.
Measure
We record the device or load, any covers or cases that stay on it, the carrying method and the environment where the piece will live. Dimensions are written on the job card before a pattern is drawn.
Draw
The cut sheet is set at full size with seam allowances, hardware positions and grain direction marked. The drawing is reviewed against the measure and signed before the first panel is cut.
Sample
A sample is built in the final canvas, liner and hardware so weight and drape are honest. The sample is fitted to the actual load and sent for approval.
Run
Approved samples are matched in batches with a stitch count per piece and the run reference on every job card. Hardware is set on the bench, never outsourced.
Fit Check
Each finished piece is loaded, closed, opened and carried before it is packed. A piece that fails returns to the bench with the reason written on the card.
Handover
Deliveries include the cut sheet reference, a care note and, where relevant, a packing diagram. The archived sample stays on the shelf for future repeat orders.
Lead times on this bench run from five working days for a single sleeve sample to six weeks for a mixed bulk run, depending on material availability and the size of the batch. Every quote states the bench slot and the delivery date in writing, and any change to either is confirmed with the client before the schedule moves.
Bring a drawing, a device or a packing list
Write to inquiries@agvasingapore.buzz or call +19434695872 during workshop hours. A short description with dimensions is enough to start a bench conversation.